Showing results: 211 - 225 of 582 items found.
-
ICS Electronics
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
ICS Electronics
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
TR8100H SII -
Test Research, Inc.
The TR8100H SII is the latest ICT with High Throughput and High Accuracy for large and complex PCBAs. The TR8100H SII is the top-of-the-line board test system targeting the low-voltage testing market.
-
402HV -
Testronics Inc.
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Acculogic Sprint 4510 -
Terotest Systems Ltd.
The Sprint 4510 family of flying probers are well known for their speed, reliability, ease of use and large world-wide installed base.Flying probe testers have few restrictions on access, require no test fixtures, and can test boards with virtually unlimited number of nets, allowing test developers to turn a program around in a short time.
-
ATE QT2256-640 PXI -
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
EV-SFP-171 -
UC Instruments, Corp.
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
1940000377-0000R -
ELMA Electronic, Inc.
The Universal 3U VPX RTM Breakout Board can allow a test engineer to access I/O signals on custom built VPX boards. The breakout board is designed for the utility, power, single ended or low speed differential signals during setup and testing of a new system. During system integration, it often is desirable to access certain utility signals such as VS1, VS2 or VS3, auxiliary voltages other signals such as Geographic address or the system management bus which are all available from the rear side of the backplane.
-
1940000352-0000R -
ELMA Electronic, Inc.
The Universal 6U VPX RTM Breakout Board can allow a test engineer to access I/O signals on custom built VPX boards. The breakout board is designed for the utility, power, single ended or low speed differential signals during setup and testing of a new system. During system integration, it often is desirable to access certain utility signals such as VS1, VS2 or VS3, auxiliary voltages other signals such as Geographic address or the system management bus which are all available from the rear side of the backplane.
-
XJDirect -
XJTAG Ltd.
XJDirect is an advanced and innovative method for programming the internal flash of your processor and implementing some aspects of board test through JTAG when traditional boundary scan techniques cannot be used.
-
Shikino High-Tech Co., Ltd.
We provide you with various inspection equipment mainly for the semiconductor post-production process. Also, "inspection boards", "measurement control" and "test applications" are available for you to meet your various needs.
-
EXC-8000cPCI -
Excalibur Systems, Inc.
The board supports up to 6 modules, and each module represents an independent test and simulation device. Most modules are based on existing Excalibur products such as the 1553 Px family and the ARINC429 RxTx.
-
K8214A -
Keysight Technologies
Keysight’s Silicon Nails feature enables all the tools required to develop and execute tests on non-compliant boundary scan devices that are connected to boundary scan compliant devices on the printed circuit board.
-
K8214B -
Keysight Technologies
Keysight’s Silicon Nails feature enables all the tools required to develop and execute tests on non-compliant boundary scan devices that are connected to boundary scan compliant devices on the printed circuit board.
-
8464 -
Technobox, Inc.
The Technobox, Inc P/N 8464 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths.